#PC CHECK 6.21 DOWNLOAD SERIAL#
#PC CHECK 6.21 DOWNLOAD DRIVERS#
#PC CHECK 6.21 DOWNLOAD MANUAL#

For example, to test CPU 0, you can select Advanced Diagnostics, and then select Processor, and then select CPU0. Most of the selections on this menu display information about the corresponding devices, and then offer a menu of testing options. See Viewing the Pc-Check Results.ДЄdvanced Diagnostics are used to test an individual device on the system. You use it to view the results of Pc-Check tests. Note - The Text File Editor command in the System Information Menu Options is of special importance. Reads sector information from the hard disks sector by sector.Д®nables you to set up startup options for diagnostics testing. Shows the I/O port assignment for the hardware devices on the system.Д®nables you to view the mapped memory for the entire system. You can choose to change the power state, view the power status, indicate CPU usage, get a power management event, or change the interface mode.

#PC CHECK 6.21 DOWNLOAD DRIVERS#

Shows device drivers loaded under Open DOS.Д®nables you to test and configure the Advanced Power Management (APM) capabilities of the system. Includes details about specific devices from pci-config space within the system, similar to the System Management Information section.

Provides information about the BIOS type, system, motherboard, enclosure, processors, memory modules, cache, slots, system event log, memory array, memory devices, memory device mapped addresses, and system boot. txt document showing your systemвЂ™s hardware ID. Includes basic information about your system, motherboard, BIOS, processor, memory cache, drives, video, modem, network, buses, and ports.Д®nables you to create an XML or. TABLE 6-1 System Information Menu Options TABLE 6-1 describes the System Information menu options. Select items in this menu to see detailed information. Navigation instructions appear at the bottom of each screen.Д¬lick System Information in the Diagnostics main menu to view the System Information menu. Use the arrow keys on the keyboard to navigate through the diagnostics software, the Enter key to select a menu item, and the ESC key to exit a menu. The Pc-Check menu provides access to the following: The following sections in this chapter describe the menu items and tests in detail. Return to the Redirection screen and follow the prompts to open the Pc-Check main menu, as shown in the following figure: The system reboots to the Pc-Check main menu.ДЎ2. Select Power On from the Select Action drop-down list box as shown in FIGURE 6-5.ДЇIGURE 6-5 ILOM 3.0 GUI: Remote Control > Remote Power Control > Power Cycle When redirection is established, return to the ILOM web interface (Remote Control tab) and select the Remote Power Control submenu.ДЇIGURE 6-4 ILOM 3.0 GUI: Remote Control > Remote Power Control ViewДЎ0. The results of the automatic tests are also written to nonvolatile memory on the SP, where they can be accessed by Sun Services.ДЇIGURE 6-3 ILOM 3.0 GUI: Remote Control > Redirection ViewД©.

#PC CHECK 6.21 DOWNLOAD SERIAL#

The output is displayed on a monitor or serial console connected to the system.

#PC CHECK 6.21 DOWNLOAD MANUAL#

Without a diagnostic partition, the only way you can see the results of Pc-Check diagnosis is to run Pc-Check in Manual mode. However, because the Sun Blade X6275 server has very limited disk space, Sun recommends that you do not create a diagnostic partition. Their results are written to a diagnostic partition, if any, on the boot disk. The other Pc-Check levels, Enabled, Extended, and Manual, will run Pc-Check automatically when the server boots. Note - The default for Run Diagnostics on Boot is Disabled, which means that Pc-Check does not run when you boot the server. For example Manual, as shown in FIGURE 6-2:ДЇIGURE 6-2 ILOM 2.0 GUI: Diagnostics View > Manual Boot Drop-down List The Diagnostics view opens as shown in FIGURE 6-1:Д¤.Дџrom the Boot drop-down list, select the level of Pc-Check diagnostics to be run. Select the Remote Control tab and then the Diagnostics tab. To Log In to the SP ILOM Web Interface DirectlyДЈ. To Log In to the SP Through the CMM ILOM Web Interface

Pc check 6.21 download